Search found 7115 matches
- Sun Jun 12, 2022 5:43 pm
- Forum: SJ series Transmission, Axles, Brakes, wheels and tyres.
- Topic: Oil capacity and grades
- Replies: 14
- Views: 51207
Re: Oil capacity and grades
Fill it till it starts to dribble out of the fill hole. Thats the right amount.
- Sat Jun 11, 2022 8:12 pm
- Forum: Builds and Projects
- Topic: Jordis 1988 Samurai (Re)Build
- Replies: 840
- Views: 571467
Re: Jordis 1988 Samurai (Re)Build
Manifolds arrived. Add that to the “sort it later pile”.
Most important thing. Move the back axle back a bit. Almost zero compression available in the prop shaft.
Pull the axle out tomorrow and redrill the perches.
Also go collect some ramps and axle stands.
Most important thing. Move the back axle back a bit. Almost zero compression available in the prop shaft.
Pull the axle out tomorrow and redrill the perches.
Also go collect some ramps and axle stands.
- Wed Jun 08, 2022 9:52 pm
- Forum: SJ series Transmission, Axles, Brakes, wheels and tyres.
- Topic: Samurai LWB wheel cylinders and brake drums
- Replies: 4
- Views: 1546
Re: Samurai LWB wheel cylinders and brake drums
Drums and cylinders should be available from a decent motor factors. Handbrake cable may be a toughy. If there is no urgency one of the Indian ebay sellers will probably have the lot. I’m going to presume the handbrake is on the rear axle? If you can’t find a cable an alternative would be to fit a t...
- Mon May 30, 2022 4:16 pm
- Forum: SJ series Transmission, Axles, Brakes, wheels and tyres.
- Topic: HELP!! No brake pedal after rear disc conv.
- Replies: 12
- Views: 3717
Re: HELP!! No brake pedal after rear disc conv.
Pleased you’re sorted bud.
- Sat May 28, 2022 6:43 pm
- Forum: SJ series Transmission, Axles, Brakes, wheels and tyres.
- Topic: HELP!! No brake pedal after rear disc conv.
- Replies: 12
- Views: 3717
Re: HELP!! No brake pedal after rear disc conv.
Not necessarily as the air can get trapped at the top of the chamber. 99% sure the caliper is designed to be fitted in the 12 o’clock position for the bleed nipple to be the highest point. I’d try bleeding them with the caliper in the top mount position. Have you also bled the whole system or just t...
- Sat May 28, 2022 5:27 pm
- Forum: SJ series Transmission, Axles, Brakes, wheels and tyres.
- Topic: HELP!! No brake pedal after rear disc conv.
- Replies: 12
- Views: 3717
Re: HELP!! No brake pedal after rear disc conv.
Are you bleeding the brakes with the caliper in the correct position?
- Fri May 27, 2022 4:21 pm
- Forum: Builds and Projects
- Topic: LJ80
- Replies: 64
- Views: 122227
Re: LJ80
Would look even better with the pictures the right way round .
Looking good though!
Looking good though!
- Mon May 23, 2022 5:47 pm
- Forum: Builds and Projects
- Topic: Jordis 1988 Samurai (Re)Build
- Replies: 840
- Views: 571467
Re: Jordis 1988 Samurai (Re)Build
I already have a custom exhaust but not the diameter required.
The new manifold comes with a 2” flange to weld onto the exhaust so i’m going to make a new 2” section that will run underneath behind the chassis then add a 2” to 2.5” adaptor to join it onto the existing stack behind the cab.
The new manifold comes with a 2” flange to weld onto the exhaust so i’m going to make a new 2” section that will run underneath behind the chassis then add a 2” to 2.5” adaptor to join it onto the existing stack behind the cab.
- Mon May 23, 2022 10:56 am
- Forum: Builds and Projects
- Topic: Jordis 1988 Samurai (Re)Build
- Replies: 840
- Views: 571467
Re: Jordis 1988 Samurai (Re)Build
Swapped a rather rattly clutch release bearing out over the weekend.
Gradually working through the little niggles.
Gradually working through the little niggles.
- Wed May 18, 2022 11:55 pm
- Forum: New members
- Topic: Hello people
- Replies: 1
- Views: 4988
Re: Hello people
Welcome to SCUK.