Advice after fitting 2/3" lift springs

Post your questions about your suspension and steering problems here!
User avatar
andyrew
SCUK is my life
SCUK is my life
Posts: 1820
Joined: Fri Jul 31, 2009 12:39 am

Re: Advice after fitting 2/3" lift springs

Post by andyrew » Sat Dec 27, 2014 10:34 am

You may find the steering wheel is now not straight.
Andys Rusty Suzuki Emporium

User avatar
ScottieJ
The Boss
The Boss
Posts: 11606
Joined: Tue Apr 15, 2008 12:13 pm
Location: Chippenham, wiltshire

Re: Advice after fitting 2/3" lift springs

Post by ScottieJ » Sat Dec 27, 2014 11:56 am

That isn't a good shackle angle to have and will give a really harsh ride. Maybe the springs will settle and flatten out improving the shackle angle after a bit of use. if not I would be inclined to remove the bottom leaf from the spring pack to help them flatten out, yes you might loose a bit of height but I would rather have a nicer ride and better flex than an extra 20mm of lift personally.
Zuki Build

Steady as she goes!

User avatar
Josh-holden
Engaged 4wd low
Engaged 4wd low
Posts: 114
Joined: Wed Nov 05, 2014 1:12 am
Location: Alcester, warwickshire

Re: Advice after fitting 2/3" lift springs

Post by Josh-holden » Sat Dec 27, 2014 3:16 pm

Ok, thanks for the comments. Do you have any ideas on what shocks i can fit?

User avatar
ScottieJ
The Boss
The Boss
Posts: 11606
Joined: Tue Apr 15, 2008 12:13 pm
Location: Chippenham, wiltshire

Re: Advice after fitting 2/3" lift springs

Post by ScottieJ » Sat Dec 27, 2014 3:38 pm

First you need to set up the bumpstops so that the springs don't get over flexed, lower them so that the axle meets them when the springs compress to the point they are flat.

Then you need to flex it up without shocks fitted and measure between the mounts to get your open and closed lengths. Then order some shocks that match these, I like to make sure the closed length is at least 1" shorter than the closed measurement that you took off the vehicle.
Zuki Build

Steady as she goes!

Tonypp
Got muddy boots
Got muddy boots
Posts: 53
Joined: Sat Jan 25, 2014 5:02 pm

Re: Advice after fitting 2/3" lift springs

Post by Tonypp » Sun Dec 28, 2014 3:38 pm

If your beast is sitting in the picture under normal road weight then the shackle looks to be on the wrong side of vertical. If that is the case the best you can hope for may be an uncomfortable ride. Yes under full compression it should move to the other side of vertical but we don't compress springs for much of the driving time. Have you tried to compress the other spring to the maximum and letting the wheel shown clear the ground, then look at the shackle. If now it has moved from the vertical to nearly parallel to the spring it could lock up. It looks like you get your toy dirty so worth checking before you drop a wheel into a deep gully and then find your have a problem.

User avatar
Naylor
Got muddy boots
Got muddy boots
Posts: 47
Joined: Thu Aug 28, 2014 12:09 pm
Location: Tidworth

Re: Advice after fitting 2/3" lift springs

Post by Naylor » Sun Dec 28, 2014 7:43 pm

Just a question but off topic , the wheels you have fitted are they a she standard wheel? As I have them on my vitara but want to know what they r off as I'm looking for a spare

Cheers

User avatar
Josh-holden
Engaged 4wd low
Engaged 4wd low
Posts: 114
Joined: Wed Nov 05, 2014 1:12 am
Location: Alcester, warwickshire

Re: Advice after fitting 2/3" lift springs

Post by Josh-holden » Sun Dec 28, 2014 9:20 pm

They where on there when I brought it. I think they are of a jimny?

User avatar
Naylor
Got muddy boots
Got muddy boots
Posts: 47
Joined: Thu Aug 28, 2014 12:09 pm
Location: Tidworth

Re: Advice after fitting 2/3" lift springs

Post by Naylor » Sun Dec 28, 2014 9:53 pm

Josh-holden wrote:They where on there when I brought it. I think they are of a jimny?
Ok cheers I'll look into it

Post Reply